The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for employ with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you need. For work with with 5/8” shaft sizes. Comes with set screws. Further Features: Made of Steel For work with with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, ideally lowering on hand requirements and allowing for adjustments in shaft size if necessary. The barrel of the split tapered bushing is normally split in two places and can be keyed to the shaft. The barrel OD is also keyed to the travel component as well. The advantage of the split tapered bushing is it will hold, even if the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.
Taper bushing are widely used as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed of high quality engineered resources with great tolerance. The feature is easy to make use of and needs no further alteration. These bushings can go well with almost all types of assemblies and sizes. They are the best choice in design for mechanical connections.
To complete designations put bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: full selection of both metric and imperial available.
Standard range meets up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete short reach range offered, for compact light and portable assemblies & Clean, Compact Style.
Simple installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Comes with 2 set screws.
Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for sturdiness and strength. U1 bushings are 
being used in an extensively wide variety of applications, which include; sprockets, shaves, pulleys, gears, plus much more, we also offer most of these products. What pieces this bushing apart may be the high-quality steel construction along with exact manufacturing and top quality control; this ensures that you always get yourself a premium quality consistent product. What really units us apart from the other folks is our experienced expert workers and our company-wide goal of customer satisfaction.
1. Be sure the tapered cone surfaces of the bushing and the inside of the driven merchandise happen to be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or different portion type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to make sure sliding suit on shaft.
4. With important on shaft, slide the sprocket or other component type to the desired posture on the shaft. Make sure you keep the heads of the cap screws attainable.
5. Align the sprocket or part type, tighten the screws on the other hand and progressively until they will be pulled up tight. Do not work with extensions on the wrench handles , nor allow the sprocket or portion to always be drawn i contact with flange of bushing. At this stage there must be a gap between your bushing flange and sprocket, make sure this gap does not close.
Twice split barrel ensures concentricity
Grips the shaft with positive clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key of all sizes for positive drive and increased torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep up concentric bores
Available in inch, metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Twice Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys on both shaft and product to supply the strongest possible drive.
3/4″ per Foot Taper on Barrel – Self locking taper provides the highest degree of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you need. For apply with 5/8” shaft sizes. Comes with set screws. Added Features: Manufactured from Steel For make use of with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, preferably lowering readily available requirements and allowing for improvements in shaft size if important. The barrel of the split tapered bushing is split in two spots and is normally keyed to the shaft. The barrel OD can be keyed to the drive component aswell. The benefit of the split tapered bushing is it will hold, even if the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.
