EP brand name alternative gearbox for woods rotary gearbox
NEW 40 HP GEARBOX Clean Enter one three/8 12 spline output Interchangable with industry well-known dimensions i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Numerous More
Characteristics
(one) brand name new forty five horse electricity shearpin gearbox. This gearbox fits many various tends to make of 4′,5′ and some 6′ rotary cutters. I promote a great deal of these containers every yr for a number of diverse programs and carry ALL Alternative Components for this box, but ideally you will not have to fret about that.
Right here are the specs on the box:
*forty five horse electricity gearbox
*Normal 1-three/8″ easy enter shaft(the place the pto shaft hooks on). The pto shaft is held on by a 1/2 shearbolt.
*length of the input shaft out of the gearbox is three” prolonged
*bolt hole sample for mounting is on the corners, 4-three/4 middle of gap to middle of hole. It requires a five/eight” bolt.
*12 splined output shaft(in which the blade provider hooks up on the bottom)
*one-9/sixteen exterior measurement in excess of the output shaft splines- from the foundation of the output cap to the end of the splines is two-3/four” long- all round duration of the output shaft is 4-1/2″ prolonged.
*will take a one” threaded castle nut and a carter crucial on the base of the output shaft to safe blade pan(NUT is integrated – – BLADE PAN IS NOT!!)
*general height of the box from the best of the mower deck to the leading of the box is nine-one/two”
This is a relatively heavy merchandise (47 lbs.) so freight is not low cost, but we do not make everything off of freight, no matter what ups fees us we demand you.
forty HP
one:1:forty seven Ratio
one-three/8″ Sleek Input Shaft with Shear Pin Hole
one-1/two” 12-Spline Ouput Shaft
Bolt Sample: 6-one/two” (four) five/eight” Holes, 5″ Centre Hole Required for Shaft Assembly
The Input and Output Shafts Can not be Obtained Serparately.
They are Bought as a kit.
The kit consists of the adhering to elements: input shaft, input equipment, output shaft, output gear.
The Shaft Package Can’t Be Separated.
EP manufacturer replacement gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Guide
Is your mower leaking, creaking or normally performing improperly? You have occur to the correct spot.
Go through underneath for the most common issues with rotary cutter gearboxes and their remedies (from fast and filthy, to skilled).
Leaking Bottom Seal:
If you’ve got wrapped some baling or fencing wire all around your output shaft and blown the seal, the expert issue to do is to exchange the seal.
If your output seal is intact, and you are able to get ID, OD and thickness measurements (in millimeters), most bearing homes can get you up a generic double-lip seal that will get you back up-and-managing. If not, give us a get in touch with and we can help you type out what you require.
A dental pick is the best way to remove the outdated seal ahead of pressing in the new one particular.
If you’re blessed sufficient to have a slow-leak, the rapid and dirty approach is to run automotive-kind grease in the gearbox until finally the new seal will come in. Be sure to examine and include grease a lot more usually than you would with oil, as this is NOT a specialist restore.
Broken Output Shaft:
Uh oh. You hit some thing that did not shift. The excellent news is that the output shaft on 
most gearboxes is pretty simple to change. The poor information is… it truly is rarely an isolated failure.
The very first issue to do is to just take apart your gearbox and assess the complete extent of the damage. If it is genuinely just the output shaft, you need to be ready to modify it out, no problem. The output shafts start at about $70 and go up in value depending on the dimension of the gearbox.
Nonetheless, in most instances, the bearings ($20/ea), seals ($10/ea) and equipment-established ($70) will also generally get a beating. If you might be unlucky, the output cap ($eighty) will also endure some hurt.
In this case, it is typically cheaper to change the gearbox. Compare the value of components to the expense of an whole, new, warrantied gearbox. At times, even specialists have to know when to get in touch with it a working day.
I Want to Change my Input Shaft:
If you are fatigued of modifying shear pins or hunting back and seeing that your mower has not been chopping, you might want to set up a slip-clutch pto shaft (Of course, we sell people as well).
This generally demands putting in a 540-fashion, 6-spline input shaft ($85) on your mower’s gearbox.
Blessed for you, we did a create-up on our weblog. It really is known as “How to alter the input shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all seem type-of related in excess of-the-cellphone. The very best point to do is to disassemble your gearbox and consider a appear at the gears and bearings. The concern will normally current by itself in the way of broken/missing equipment enamel, toasted gears (like that photo on our residence page), or blown bearings.
If every little thing looks regular, try out modifying the gear-mesh. This is carried out with the mylar “gaskets” that sit among the principal gearbox case and the enter/output caps. Consider adding or taking away some of these spacers until your gears have around one/eight”-one/4″ of free of charge play. Pros can order replacements ($one-two) in varying thicknesses, but we suggest the quick and filthy approach of slicing your very own out of a sheet of mylar.
Will not neglect to re-seal the gearbox with RTV following you have found the appropriate mixture. Even even though they are referred to as “gaskets”, they will not likely seal your gearbox on their own.
Do you have any kind of referrals on the Interpump Gearbox For PTO Drive? Please do not be reluctant to call us.
